
A customer needed yellow vitamin pellets for a capsule product, and sent only a finished sample. There was no process description, no binder recommendation, and no set of operating parameters. JIANPAI’s laboratory developed the full route—seed starting, scale-up granulation, drying, and coating—and reached a comparable appearance, controlled particle size, and a yield above 95% on the first trial.
This case study is written for B2B pharmaceutical and nutraceutical teams who must turn a reference sample into a repeatable pellet process, and who want to see how a JZB-B centrifugal granulator and a high-efficiency coating machine were paired to do that work.
Need a pellet process built from a sample, not only a machine quote?
Share your target size, appearance, and batch range with the JIANPAI process team and review centrifugal granulation and coating options before you lock the line design.
Table of Contents
ToggleThe customer’s capsule fill contained yellow vitamin pellets with vitamin C, vitamin B1, vitamin B6, vitamin B12, and folic acid. The only physical reference was that target sample. Every step that would normally arrive in a tech-transfer pack—how to start seeds, which binder to use, how fast to add powder, how to dry, and how to coat—had to be designed and verified in the lab.
JIANPAI’s laboratory took on that brief and chose to develop the process independently, rather than wait for a customer recipe that did not exist.
Three constraints defined the trial:
The laboratory designed a four-stage route: seed starting, scale-up granulation, drying, and coating. A JZB series centrifugal granulator was used for seed starting, scale-up granulation, and spheronization. A JIANPAI high-efficiency coating machine was then used both to dry the pellets and to apply the coating.
That pairing matters for sample-only projects. Centrifugal granulation can grow pellets layer by layer in one closed bowl, which is why it is often compared with multi-step extrusion-spheronization in JIANPAI’s CIPM 2026 Q&A on centrifugal granulation. Drying and coating in a pan coater then keeps the batch in a controlled finishing step without adding a separate dryer to the first-trial setup.
JIANPAI centrifugal granulator: seed starting and pellet growth.
JIANPAI high-efficiency coating machine: drying and coating. See also the JGB-E fully automatic tablet coating machine and the tablet coating range.
The experiment ran in three recorded stages. Table 1 lists charge, recovered mass, particle size, and duration. Granulation took place on 14 November 2026; coating was completed on 18 November 2026.
Table 1. Key parameters and results for the yellow vitamin pellet trial
| Stage | Charge | Recovered | Particle size | Duration |
|---|---|---|---|---|
| Granulation (14 Nov) | 7 kg (1 kg seed start + 6 kg added stepwise) | 6.5 kg | 0.8–1.1 mm (sieved; 1.0 mm fraction retained) | 30 minutes |
| Drying (in the coating machine) | 6.5 kg | 6 kg | — | 1 hour |
| Coating (18 Nov) | 5 kg | 4.860 kg | 1.0–1.2 mm | 35 minutes |
Granulation reached a stable size band of 0.8–1.1 mm in 30 minutes. The pellets were then dried for one hour in the coating machine. Coating used a shellac solution and was completed in 35 minutes, with a finished size of 1.0–1.2 mm.
With no customer process in hand, the laboratory obtained a successful result on the first trial: the pellets formed well, sphericity was high, particle size stayed in the target window, and overall yield was above 95%. After coating, the appearance was comparable to the customer sample, as shown in Figure 1 and Figure 2. The full route was opened in a single pass, without repeated rework cycles.
Figure 1. Coated yellow vitamin pellets compared with the customer sample.
Figure 2. Finished yellow vitamin pellets from the first trial.
Planning a centrifugal pellet trial of your own?
Ask JIANPAI to review target size, coating, and batch time against laboratory practice before you specify equipment.
Three operating choices helped the trial stay efficient and keep yield high:
Buyers comparing coating hardware can also use JIANPAI’s guide to choosing a tablet coating machine when the same finishing step must later move from laboratory scale to production.
The value of this case is not only that a machine can run a vitamin formula. It is that the laboratory can design and verify a preparation process when the customer has a target sample and nothing else. That is the practical meaning of JIANPAI’s “equipment plus process” support: seed starting, growth, drying, and coating are developed together, then documented with mass balance, size, and cycle time that a buyer can take into later scale-up discussions.
If you are sourcing a centrifugal granulator or a coating machine for pellet work, treat a sample-based trial as part of the procurement conversation, not as an afterthought after the purchase order.
Can JIANPAI develop a vitamin pellet process from a sample only?
Yes. In this laboratory case, the customer provided a target sample and no process parameters. The lab designed seed starting, scale-up granulation, drying, and coating, and obtained a comparable appearance and a yield above 95% on the first trial.
What equipment was used to make the yellow vitamin pellets?
A JZB series centrifugal granulator was used for seed starting, scale-up granulation, and spheronization. A JIANPAI high-efficiency coating machine was used to dry the pellets and to apply a shellac coating.
What particle size and yield were achieved?
After granulation, pellet size was 0.8–1.1 mm, with the 1.0 mm fraction retained after sieving. After coating, size was 1.0–1.2 mm. Overall yield was above 95%.
Why were the pellets dried in the coating machine?
The laboratory used the coating machine for a one-hour drying step before shellac coating. That kept drying and coating in one finishing unit for this first-trial setup, rather than adding a separate dryer to the route.
How long did one batch take?
Granulation took 30 minutes, drying one hour, and coating 35 minutes. The laboratory reported that a coated pellet batch could be completed in about two hours from granulation through coating.
Can undersize pellets and fines be reused?
Yes. In this trial, smaller pellets and fine powder were returned as starter seeds, which improved material utilization and reduced waste.